Question 1

What is an airgun and how is it different from a firearm?

Accepted Answer

An airgun launches a projectile using compressed gas, compressed air, or a spring-driven piston rather than burning gunpowder. Federal law (18 USC 921) defines a firearm as a weapon that expels a projectile by the action of an explosive, so airguns sit outside that definition and are regulated more like consumer products at the federal level. They still launch real projectiles at lethal velocities in many cases, so they should be handled with the same discipline as a firearm. State and city rules vary, with New Jersey and Rhode Island treating airguns as firearms and New York City requiring a license.

Question 2

What are the major airgun power types?

Accepted Answer

The four common power types are PCP (pre-charged pneumatic), break barrel (which uses either a coiled spring or a gas piston), multi-pump pneumatic, and CO2. PCPs store high-pressure air in an onboard reservoir for many shots per fill. Break barrels generate compressed air on each shot by cocking a spring or gas ram. Multi-pumps build pressure with several strokes of an onboard pump. CO2 guns use 12-gram cartridges or larger bulk tanks of liquefied carbon dioxide. Each has different tradeoffs for cost, complexity, power, and shot consistency.

Question 3

When does a PCP make sense for a new shooter?

Accepted Answer

A PCP makes sense when you want the best accuracy, low recoil, and many shots per fill, and you are willing to invest in a fill source like a hand pump, scuba tank, or compressor. PCPs dominate competition and serious airgun hunting because the shot cycle is dead-still and most modern PCPs are regulated for shot-to-shot consistency. The downsides are higher entry cost and the extra equipment to put air into the gun. If you only want to shoot once in a while in the backyard, a break barrel or CO2 gun is simpler.

Question 4

When does a break barrel make sense?

Accepted Answer

A break barrel makes sense when you want a self-contained gun with no fill equipment, no cartridges, and no recurring costs beyond pellets. You cock the gun by breaking the barrel down, load a pellet directly into the breech, snap it closed, and shoot. They are great for plinking, pest control, and backyard shooting in calibers like .177 and .22. The tradeoff is that spring and gas piston guns are hold-sensitive and have a unique double recoil that demands the artillery hold to shoot accurately.

Question 5

When does a CO2 gun make sense?

Accepted Answer

A CO2 gun makes sense for casual plinking, backyard target shooting, and training, especially when you want a realistic feel of a semi-auto pistol or rifle. They are inexpensive to operate and require no pumping or filling beyond installing a 12-gram cartridge. The catch is that CO2 is temperature-sensitive: performance falls off in cold weather and improves in heat, and rapid shooting cools the gun and drops velocity. They are not the right tool for serious hunting at distance.

Question 6

When does a multi-pump make sense?

Accepted Answer

A multi-pump makes sense for a low-maintenance, all-in-one outdoor gun, especially for younger or new shooters who want variable power. You pump the forearm a set number of times to build pressure (typically 3 to 8 pumps on classics like the Benjamin 392), then load and shoot. Fewer pumps is quieter and lower power for plinking; more pumps is for hunting small game. There are no cartridges to buy and no air tanks to fill. The downside is slower follow-up shots and more physical effort over a long session.

Question 7

What is FPS and what is FPE?

Accepted Answer

FPS is feet per second, which measures velocity at the muzzle. FPE is foot-pounds of energy, which measures the actual kinetic energy the projectile carries. The formula is FPE = (weight in grains x velocity squared) / 450240. FPE matters more than raw FPS because a heavy pellet at moderate velocity often produces more energy and penetrates better than a light pellet shot fast. Manufacturers love to advertise high FPS using the lightest alloy pellets, which is misleading for hunting purposes.

Question 8

How much FPE do I need?

Accepted Answer

For paper plinking and BB targets, even 3 to 6 FPE is enough. For ethical small game hunting (squirrel, rabbit, starling) the broadly accepted minimum is around 12 FPE delivered to the target with a vital-zone hit. For larger pests like raccoons or for longer ranges, 20 to 30 FPE is more appropriate. Big-bore airgun hunting for deer-sized game requires far more, with several states setting minimums in the hundreds of foot-pounds. Always check your state regulations before hunting.

Question 9

Is a high FPS number always better?

Accepted Answer

No. A high FPS number on the box usually comes from the lightest, cheapest alloy pellet a manufacturer can find, and those pellets often have terrible accuracy. Heavier lead pellets at lower velocity routinely deliver more energy at the target, more accuracy, and less wind drift. Above roughly 1,100 FPS, lead pellets often turn supersonic and become inaccurate due to transonic instability. Chase accuracy and FPE, not the headline FPS.

Question 10

What does .177 caliber do best?

Accepted Answer

.177 is the most popular caliber worldwide, the only caliber accepted in international 10-meter Olympic competition, and the cheapest to feed. Pellets are light and fast, giving the flattest trajectory of any common airgun caliber, which is why target shooters prefer it. It is a fine pest and small-game caliber inside about 25 yards when you have at least 12 FPE and place shots well. The drawback is less knockdown energy than larger calibers at distance.

Question 11

What does .22 caliber do best?

Accepted Answer

.22 is the all-around hunting caliber and is generally considered the best balance for small game and pest control out to about 50 yards. A given airgun in .22 will produce roughly 20 percent more energy than the same gun in .177, and the heavier pellet bucks wind better and dumps more energy on impact. The trade is a more curved trajectory than .177 and slightly higher pellet cost. For most hunters, .22 is the right first hunting caliber.

Question 12

When should I step up to .25, .30, .35, or larger?

Accepted Answer

Step up when you need more energy at distance or for tougher game. .25 is popular for raccoon and crow-sized pests at 50 to 75 yards from a powerful PCP, and .30 is the entry to true long-range and small-deer-class hunting. .35, .45, and .50 are big-bore territory used for hogs, predators, and even deer-sized game in states that allow it. Texas requires at least .30 caliber, a 150-grain bullet, and 215 ft-lbs muzzle energy for deer-class game, while Virginia requires at least .35 caliber for deer. Larger calibers eat air fast and shot count drops.

Question 13

What should a first-time buyer get for paper targets and plinking?

Accepted Answer

A .177 break barrel in the 8 to 12 FPE class, or a quality multi-pump like a Benjamin 392/397, will plink happily for years with no fill equipment. If budget allows and you want maximum ease and accuracy, a regulated .177 or .22 PCP plus a hand pump is hard to beat. CO2 guns are also excellent for casual indoor or backyard plinking. Avoid the highest-velocity magnum springers as a first gun; they are loud, hard to cock, and unforgiving of poor technique.

Question 14

What should a first-time buyer get for small-game hunting?

Accepted Answer

A .22 caliber rifle producing at least 12 FPE at the muzzle is the standard answer. A regulated .22 PCP gives the easiest path to consistent accuracy. A quality .22 break barrel works too if you commit to learning the artillery hold. Pair the gun with an airgun-rated scope, a good supply of mid-weight domed pellets, and a chronograph so you can confirm your real velocity and energy.

Question 15

What should a first-time buyer get for pest control?

Accepted Answer

For close-range pests in a populated area, prioritize a quiet, accurate gun. A shrouded or moderated .22 PCP at 18 to 25 FPE handles rats, pigeons, and starlings cleanly while keeping noise low. A .177 PCP at 12 to 18 FPE is a great choice for indoor barn pests because pellets are less likely to over-penetrate. Always confirm local ordinances; some cities restrict discharge of any projectile-launching device within city limits even if state law is permissive.

Question 16

What should a first-time buyer get for competition?

Accepted Answer

For 10-meter Olympic-style target shooting, you need a .177 single-shot match rifle or pistol such as those made by Feinwerkbau, Walther, Steyr, or Anschutz, and a recoilless platform (PCP or single-stroke pneumatic). For field target, a regulated .177 PCP in the 12 to 20 FPE range plus a high-magnification adjustable parallax scope is the standard. For benchrest, larger calibers (.22 to .30) on heavy regulated PCPs dominate. Talk to your local club before buying, because match rules dictate the gun.

Question 17

How does a PCP airgun work?

Accepted Answer

A PCP stores high-pressure air (typically 2,000 to 4,500 PSI) in an onboard reservoir or removable bottle. When you pull the trigger, a hammer strikes a valve that opens for a fraction of a second, releasing a precisely metered burst of air behind the pellet. Because only air moves at firing, recoil is minimal, the lock time is short, and accuracy potential is very high. Once the reservoir runs low, you refill from a hand pump, scuba/SCBA tank, or HPA compressor.

Question 18

What equipment do I need to fill a PCP?

Accepted Answer

You need one of three things: a high-pressure hand pump rated to 3,000 or 4,500 PSI, a scuba/SCBA tank with the right fill adapter, or an electric HPA compressor. Hand pumps are the cheapest entry but are physical work and pull moisture into the gun if not filtered. Tanks are fast and convenient but need to be refilled at a dive shop or paintball store. Compressors are the most convenient and most expensive, and they need regular maintenance of filters and seals.

Question 19

What is fill pressure and why does it vary by gun?

Accepted Answer

Fill pressure is the maximum air pressure the manufacturer specifies for the onboard reservoir, and it varies because reservoirs are engineered to specific working pressures. Common values are 200 bar (2,900 PSI) and 300 bar (4,350 PSI). Filling above the marked maximum stresses the reservoir, can damage the regulator or burst disk, and on unregulated guns can actually reduce velocity by causing valve lock. Always fill to the manufacturer's number and no higher.

Question 20

What is the difference between max fill and the sweet spot?

Accepted Answer

Max fill is the upper pressure limit set by the manufacturer. The sweet spot is the pressure range over which the gun produces its most consistent velocity, which on an unregulated PCP is usually a band somewhere below max fill. On many guns the bell curve peaks below max fill, so filling all the way to the top can briefly suppress velocity (valve lock) before it climbs as pressure drops. A chronograph and a few shot strings will reveal your specific gun's sweet spot.

Question 21

What does a regulator do and why does it matter?

Accepted Answer

A regulator sits between the high-pressure reservoir and the firing valve. It bleeds reservoir air down to a fixed lower pressure (the setpoint, often 100 to 200 bar) into a small chamber called the plenum, so each shot fires from the same pressure regardless of how full the reservoir is. The result is a flat shot string with very low extreme spread, often under 10 fps over many shots, until the reservoir drops below the setpoint. Most modern serious PCPs are regulated.

Question 22

How do I track my pressure curve and shot count?

Accepted Answer

Use a chronograph and shoot the gun from a full fill all the way down, recording velocity every shot. On an unregulated gun you will see velocity start low, climb to a plateau, and fall off. Pick the band where velocity stays within an acceptable spread (often within 25 fps) and that is your usable shot count. On a regulated gun you will see a flat plateau and then a sharp drop the moment the reservoir falls below the setpoint, which tells you exactly when to refill.

Question 23

Can you overfill a PCP?

Accepted Answer

Yes, and you should not. Overfilling stresses the reservoir, regulator, gauge, and burst disk and can degrade or fail components. On an unregulated gun, overfilling often produces lower velocity, not more, because the hammer cannot open the valve fully against excess pressure (this is called valve lock). A regulator does not let you safely fill the reservoir higher than the rated pressure; the regulator only controls downstream pressure. Stick to the marked max fill.

Question 24

What is a buddy bottle or external tank tether?

Accepted Answer

A buddy bottle is a removable air bottle that screws onto the gun in place of an integral tube, often holding 300 to 500 cc, which lets you swap in a fresh full bottle in seconds. Tethering means leaving a fill hose connected from a larger tank to the gun while you shoot, so the gun is constantly topped off. Tethering is great for benchrest and tuning but limits mobility. Both approaches extend shooting sessions far beyond a single onboard fill.

Question 25

What is a plenum and why does it matter?

Accepted Answer

The plenum is the small reservoir of air between the regulator and the firing valve. It holds the metered shot of air at the regulator's setpoint pressure, ready to be released the instant the valve opens. If the plenum is too small for the power level you want, pressure drops sharply during the shot and you lose energy. A general guideline among tuners is roughly 0.5 to 1 cc of plenum volume per FPE of intended power. Plenum volume is one of the main variables in a tune.

Question 26

How do I safely degas a PCP?

Accepted Answer

Many PCPs include a degassing tool, port, or procedure that lets you bleed the reservoir to zero in a controlled way. On a regulated gun, the safest method is usually to slowly loosen the regulator gauge or use the manufacturer's bleed screw to release pressure gradually, never all at once and never with the gun pointed at anyone. The slow alternative is to dry-fire the gun until it stops cycling. Always consult your owner's manual; never disassemble a pressurized PCP.

Question 27

Should I store a PCP empty or pressurized?

Accepted Answer

Store a PCP pressurized, ideally at or near its working fill pressure or at the regulator setpoint. The pressure keeps internal o-rings seated and seals from drying out. Long-term empty storage is the most reliable way to develop slow leaks the next time you fill the gun. If you must travel and absolutely cannot ship a pressurized airgun, fully degas it per the manufacturer's procedure rather than just bleeding partly.

Question 28

Is a hand pump enough or do I need a compressor?

Accepted Answer

A hand pump is enough for light shooters, especially on small-reservoir guns, where 30 to 80 pumps tops the gun off after a session. It is labor-intensive once a tank is empty (several hundred pumps from zero) and can introduce moisture if you do not drain the pump's water trap. If you shoot a lot, run a high-volume gun, or fill big bottles, a compressor or scuba tank quickly becomes worth the money.

Question 29

What is hammer spring adjustment?

Accepted Answer

The hammer spring controls how hard the hammer hits the firing valve, which controls how long the valve stays open and how much air is dumped per shot. On many guns this is user-adjustable. Heavier hammer strike opens the valve longer for more power, at the cost of air efficiency. Lighter strike yields more shots per fill at lower velocity. Hammer spring adjustment is a common first tuning step paired with regulator setpoint changes.

Question 30

How does a spring piston airgun work?

Accepted Answer

When you cock the gun by breaking the barrel down (or pulling an underlever or sidelever), a heavy steel spring is compressed behind a piston. Pulling the trigger releases the spring, which slams the piston forward and compresses a column of air ahead of it. That compressed air rushes through a transfer port and pushes the pellet down the barrel. Because the piston moves before the pellet leaves, the gun has a unique double recoil pulse that demands proper technique.

Question 31

What is a gas piston (gas ram, nitro piston) and how is it different?

Accepted Answer

A gas piston replaces the coiled steel spring with a sealed cylinder of compressed gas, usually nitrogen. Cocking the gun further compresses that gas; releasing the trigger lets it expand and drive the piston forward. Compared to a coil spring, a gas piston cocks more linearly, has less vibration and twang, can be left cocked for hours without spring fatigue, and is less affected by cold weather. Coil springs are cheaper, more easily tuned by hobbyists, and replaceable; gas rams are usually replaced as a unit if they fail. Accuracy potential is similar.

Question 32

Why are break barrels hold-sensitive?

Accepted Answer

The pellet is still inside the barrel while the piston slams forward, so the gun moves a measurable amount during the shot cycle (lock times of 5+ milliseconds for spring guns, vs about 2-3 ms for centerfire rifles). Any inconsistency in how you hold or rest the gun changes where the muzzle is pointing when the pellet finally exits, which throws point of impact around. The fix is the artillery hold and consistent technique, not gripping the gun harder.

Question 33

What is the artillery hold?

Accepted Answer

The artillery hold is a deliberately loose, repeatable hold that lets the gun recoil freely, the way a field artillery piece sits in its carriage. Rest the forestock on an open, flat palm at the gun's balance point, keep fingers relaxed, hold the pistol grip lightly, and let the gun bounce on the shot. The point is being identical from shot to shot, not being floppy. The name was popularized by Tom Gaylord. Once mastered, group sizes typically shrink dramatically with the same gun and pellet.

Question 34

What does cocking effort tell me?

Accepted Answer

Cocking effort is the pounds of force needed to break the barrel and compress the spring, and it usually scales with power. Entry-level guns are around 18 to 25 pounds, magnum springers can exceed 35 to 45 pounds. Higher cocking effort makes the gun harder to shoot a lot, harder for younger or smaller shooters, and is correlated with harsher shot cycles. For most adults, 25 to 30 pounds is a comfortable upper limit for a session of hundreds of shots.

Question 35

What is barrel droop and how do I fix it?

Accepted Answer

Barrel droop is when the barrel points slightly downward relative to the receiver where the scope is mounted, so even with the scope's elevation cranked all the way up, the gun shoots low. It is common on break barrels because the barrel pivots on a hinge and tolerances stack up. The fixes, in order of preference, are an adjustable scope mount such as the BKL adjustable, a droop-compensating one-piece mount, Burris Signature rings with offset inserts, or carefully shimming the rear ring. Avoid maxing out the scope's internal elevation, which causes the reticle to drift.

Question 36

Why should I never dry-fire a spring piston airgun?

Accepted Answer

Without a pellet to push against, the piston slams forward unimpeded and the seal smashes into the end of the compression chamber at full speed. Repeated dry-firing can shatter the piston seal, break the spring, and crack the receiver in extreme cases. A few accidental dry-fires will not destroy the gun, but make it a habit not to dry-fire. Gas piston guns are slightly more tolerant but the same rule applies.

Question 37

What is dieseling and is it bad?

Accepted Answer

Dieseling is the combustion of lubricating oil inside the compression chamber when the piston compresses air to roughly 2,000 degrees F per shot. A small amount is normal in many spring guns and even contributes a little energy. Heavy dieseling produces white smoke, sharp crack-like reports, and erratic velocity, and indicates too much oil or the wrong oil. Detonation (a louder bang) can damage seals and the spring. The fix is to run the gun until excess oil burns off and to use only manufacturer-recommended chamber lubes going forward.

Question 38

What lubricants are safe for a spring gun and which should I avoid?

Accepted Answer

Use silicone chamber oil (high flashpoint) on the piston seal and breech seal, applied a drop or two every 1,000 shots or when the seal squeaks on cocking. Use a thin film of moly or lithium grease on the spring; avoid heavy tar greases that trap dust and feed dieseling. Never use petroleum-based oils (WD-40, 3-in-1, motor oil) inside the compression chamber of a modern springer with synthetic seals: they cause dieseling, swell or rot synthetic seals, and can detonate. RWS Chamber Lube and Pellgunoil are common safe choices.

Question 39

How does a CO2 airgun work?

Accepted Answer

The gun pierces a CO2 cartridge or draws from a bulk tank, exposing the pellet path to liquid CO2 that is constantly evaporating into a high-pressure gas. At room temperature, that gas sits at roughly 850 to 1,000 PSI. When you pull the trigger, a valve opens briefly to release a metered puff of gas behind the pellet. The cartridge stays usable until the liquid CO2 is exhausted and gas pressure drops too low to cycle the gun.

Question 40

What is the difference between 12g cartridges, bulk fill, and 88g AirSource?

Accepted Answer

A 12-gram cartridge (Powerlet) is the most common single-use cartridge and yields roughly 30 to 60 useful shots in a typical pistol or rifle. Bulk fill systems use a refillable tank or paintball-style bottle to feed liquid CO2 into a larger onboard reservoir for hundreds of shots before refill. Crosman's 88-gram AirSource and similar 90-gram cartridges are large single-use cartridges used on certain rifles for many more shots than a 12g without paintball-tank infrastructure.

Question 41

How does temperature affect CO2 performance?

Accepted Answer

CO2 pressure is set by temperature, not by how full the cartridge is, so cold weather drops pressure and hot weather raises it. On a cold winter day a CO2 pistol might give 30 shots before pressure falls too low to cycle, while the same gun on a warm summer day delivers 60 shots and higher velocity. Rapid shooting also chills the gun as liquid CO2 vaporizes, so velocity sags within a string. Below about 50 degrees F, CO2 guns become unreliable.

Question 42

How do I know when my CO2 cartridge is running low?

Accepted Answer

Velocity starts to drop noticeably and the gun gets quieter shot-to-shot. On semi-autos, the slide may stop locking back or the action may fail to cycle. On bolt-action rifles, you will feel weaker recoil and see noticeable pellet drop on target. When that starts, fire any remaining shots into a safe trap or release the rest of the gas, then change the cartridge. Do not store the gun with a partially used cartridge for extended periods.

Question 43

How do I avoid leaks from a pierced cartridge?

Accepted Answer

Apply one drop of Pellgunoil (or equivalent CO2-rated oil) to the tip of each new cartridge before installing. The oil rides into the gun on the gas and conditions the seal where the cartridge is pierced. Tighten the piercing screw firmly but not gorilla-tight. Replace the seal if the gun starts to leak after the cartridge is installed; that is the first place to look before assuming a deeper problem.

Question 44

Should I leave a CO2 cartridge in the gun or release it after each session?

Accepted Answer

Both schools have merit. Leaving a partial cartridge installed keeps the seals pressurized so they stay seated, but it accelerates wear on the seal and any slow leak will empty the cartridge anyway. Most experienced CO2 shooters fire the cartridge to empty (or release it) at the end of each session, then store the gun unpressurized. If you do leave a cartridge in, plan to use it up within a week or so. Never store a CO2 gun in a hot car: temperature spikes can rupture cartridges.

Question 45

Are all 12-gram CO2 cartridges the same?

Accepted Answer

Functionally, yes. All 12-gram cartridges hold the same 12 grams of liquid CO2 at the same vapor pressure, regardless of brand. Real differences are quality control on the seal, weld, and neck dimensions. Some compact pistols are picky about cartridge length and neck taper. Threaded versions exist for specific platforms. Buying in bulk from established brands (Crosman, Umarex, Leland) keeps the per-cartridge cost reasonable.

Question 46

How does a multi-pump pneumatic work?

Accepted Answer

You operate a forearm-mounted lever (or a butt-mounted pump arm on some designs) several times to compress air into a small onboard reservoir. Each pump adds a controlled amount of air. When you fire, all that stored air is released in a single shot, then the reservoir is empty until you pump again. The gun has no spring slamming forward and no cartridge to buy, which is why multi-pumps like the Benjamin 392/397 and Sheridan Blue Streak have stayed popular for over half a century.

Question 47

What are the minimum and maximum pumps and why does it matter?

Accepted Answer

Most multi-pumps specify a minimum (usually 3 pumps) and a maximum (often 8 to 10). Below the minimum, the seals do not seat and pressure can leak past or cycle improperly. Above the maximum, you stress the seals and reservoir and can lock the valve so it cannot open. Going past the manufacturer's max gains you almost no extra velocity (often only 5 to 15 fps for the last pump on most guns) at significant cost in wear. Stick to the published range.

Question 48

Can I vary power by changing pump count?

Accepted Answer

Yes, that is one of the multi-pump's signature features. Three pumps might give you 450 to 500 fps for quiet plinking; eight pumps gets the same gun up to its rated 685+ fps for hunting. Use fewer pumps for indoor or close-range targets to reduce noise and over-penetration; use the full count when you need terminal energy. Always pump consistently for any given target distance so your zero stays repeatable.

Question 49

Should I store a multi-pump pumped or empty?

Accepted Answer

Store it with one pump of air in the reservoir, no more. That single pump keeps the seals seated and from drying out, but does not stress them. Never store a multi-pump fully pumped; that is a recipe for stretched seals and slow leaks. Never store it completely empty for long periods either; the seals can shrink. One pump is the universal recommendation in the Benjamin and Sheridan manuals.

Question 50

What is a wadcutter pellet and when do I use it?

Accepted Answer

A wadcutter has a flat face. It is designed to punch crisp, easy-to-score holes in paper targets, which is why it is the standard for 10-meter competition. The flat face creates high drag, so wadcutters are best inside about 25 yards. Beyond that, they shed velocity quickly and group sizes open up. They also work well for short-range pest control on small animals because they transfer energy efficiently and do not over-penetrate.

Question 51

What is a domed pellet and when do I use it?

Accepted Answer

A domed (round-nosed) pellet has a rounded head and is the most aerodynamic common shape. Domed pellets are the all-around best choice for almost any airgun and almost any task beyond paper-punching: hunting, long-range target, plinking, pest control. They retain velocity and energy at distance, group well, and are less wind-sensitive than other shapes. JSB Exact, H&N Field Target Trophy, and RWS Superdome are popular examples. If in doubt, start with a domed pellet.

Question 52

What is a pointed pellet and when do I use it?

Accepted Answer

A pointed pellet has a sharp tip designed to penetrate harder targets like thick-skinned game or plastic spinners. In practice, pointed pellets are usually no more accurate than domed pellets and often less so, because the sharp tip is harder to manufacture concentrically. Domed pellets penetrate about as deep in lead testing. Try pointed pellets if your gun likes them, but do not expect them to outshoot a quality domed pellet.

Question 53

What is a hollow point pellet and when do I use it?

Accepted Answer

A hollow point has a cup or cavity in the head designed to expand on impact, dumping more energy into soft tissue and limiting over-penetration. They work best at short range from medium- to high-powered airguns; expansion typically requires impact velocities around or above 600 to 800 fps depending on design. They are a hunting pellet for squirrel- and bird-sized game inside about 30 yards. At long range or low velocity, the hollow point does not expand and the cavity actually hurts the ballistic coefficient.

Question 54

How does pellet weight affect velocity and energy?

Accepted Answer

A heavier pellet starts slower than a light pellet from the same gun, but loses velocity more slowly downrange and resists wind better. Energy depends on both: FPE = (weight x velocity squared) / 450240. In most airguns, mid-weight to heavy pellets actually deliver more energy at the muzzle and far more at 50 yards than the lightweight alloys advertised on the box. Light alloys gain advertised FPS at the cost of ballistic coefficient and accuracy.

Question 55

What are slugs and how are they different from pellets?

Accepted Answer

A slug is a solid, bullet-shaped projectile with no diabolo waist or hollow skirt. Slugs are denser and longer than pellets, have higher ballistic coefficients, and retain energy and accuracy at extended ranges (often 100 yards or more). They require a fast-twist barrel (typical 1:16 to 1:20) to spin-stabilize them, while pellets are drag-stabilized and prefer slow twists. Slugs need significant power to push them accurately and are mostly used in tuned PCPs producing 30 FPE and up. They are not a beginner's first ammo.

Question 56

How do I find the right pellet for my gun?

Accepted Answer

Buy a sample pack or three or four tins of different brands, weights, and head shapes (domed is the right starting place). Shoot 5- or 10-shot groups at a representative distance (25 yards is a good benchmark) using identical hold and rest. The pellet that produces the smallest group consistently is your gun's pellet, full stop. Do not trust online forums; barrels vary even within the same model. Plan to spend an afternoon and a few hundred pellets on this; it is the single highest-leverage thing you can do for accuracy.

Question 57

Why do cheap pellets hurt accuracy?

Accepted Answer

Pellet accuracy depends on tight tolerances on weight, head diameter, skirt diameter, and concentricity. Cheap pellets are made fast in worn dies, so weights vary by half a grain or more, head sizes vary by hundredths of a millimeter, and skirts have flash and burrs that throw the pellet off-axis. The result is fliers and group sizes 2 to 5 times larger than quality pellets. Brands like JSB, H&N, Air Arms, and RWS are the consensus quality benchmarks.

Question 58

What is skirt quality and why does it matter?

Accepted Answer

The skirt is the thin, hollow rear of a diabolo pellet. It must be slightly larger than bore size so the air pressure expands it (obturation) and seals the bore. A damaged, out-of-round, or too-small skirt blows by air, drops velocity, and tumbles the pellet. Inspect skirts visually before loading; flash, dents, or split skirts go in the discard pile, not the gun. Skirt quality is one of the biggest reasons premium pellets shoot tighter than budget pellets.

Question 59

How do I measure pellet fit and head size?

Accepted Answer

A PelletGage is a precision laser-cut sheet with calibrated holes (usually in 0.01 mm steps) for sorting pellets by head diameter. Drop pellets through and they fall through the smallest hole that fits the head, indicating its size. JSB, H&N, and Air Arms publish target head sizes on their tins (e.g., 4.51, 4.52, 4.53 mm in .177). Match the size your barrel likes; many guns prefer 4.52 mm in .177 or 5.52 mm in .22, but it is barrel-specific. Calipers work too but are slower and less repeatable.

Question 60

What is the difference between a pellet and a BB?

Accepted Answer

A pellet is a lead (or lead-alloy) diabolo with a solid head and hollow skirt, sized in calibers like .177 and .22. A BB is a small, hard, round steel ball, typically 4.4 to 4.5 mm. BBs are cheap and fed from magazines for fast, plinking-style shooting from smoothbore guns. Pellets are far more accurate at any range past close-up because their shape stabilizes them in flight and their soft lead engages rifling.

Question 61

Can I shoot BBs in a rifled barrel?

Accepted Answer

Steel BBs in a rifled barrel will erode the rifling over time, gradually destroying accuracy with pellets. Some dual-ammo guns have polygonal or shallow rifling designed to tolerate both, but they are a compromise. If your gun is sold as pellet-only, do not shoot BBs in it. If you must shoot round projectiles in a rifled barrel, use lead BBs (Smart Shot, Gamo round lead) which are soft enough not to damage the rifling.

Question 62

How often should I clean an airgun barrel?

Accepted Answer

Less often than you would expect. Most airgun barrels run best with a thin film of lead deposited from previous shots, and many shooters never clean their barrels at all. The right time to clean is when accuracy clearly degrades from its baseline, typically anywhere from 500 to several thousand shots depending on barrel, pellet, and velocity. Higher velocity (above 900 fps) and harder pellets (with antimony) lead more quickly. Use cleaning pellets, a pull-through with a patch, or a quality coated rod from the breech end.

Question 63

Why is over-cleaning a problem?

Accepted Answer

A freshly cleaned bare-metal barrel often shoots worse than the same barrel with a thin lead film. After a deep clean, expect 30 to 200 shots before accuracy returns as the bore leads in again. Aggressive bronze brushing wears the bore. Steel rods bouncing against the crown can damage the muzzle, which directly hurts accuracy. The rule is: do not clean unless accuracy has actually fallen off, and when you do, clean gently from the breech with a patch and light solvent.

Question 64

How do I care for o-rings?

Accepted Answer

External o-rings on fill probes, fill ports, and bottle threads need an occasional smear of silicone grease (diver's silicone, not petroleum). Internal o-rings on PCP valves and regulators are factory lubed and usually last a decade or more without intervention. If a PCP starts leaking, the most common culprits are the fill probe o-ring, the gauge o-ring, or the burst disk. Replacement o-rings should match the size and material (Buna-N or Viton) the manufacturer specifies.

Browse all airgun questions

Getting Started18

PCP Airguns14

Break Barrel / Spring Piston9

CO2 Airguns7

Multi-Pump Airguns4

Ammunition & Pellets13

Maintenance & Care9

Safety8

Shooting Fundamentals11

Buying & Selling7